• 100% Solids Epoxy Pre-Primer

    100% Solids Epoxy Pre-Primer

    V155

    Show Details

    100% Solids Epoxy Pre-Primer is formulated for use on both steel and masonry. For rusted steel where extensive surface preparation is needed, but not logistically possible, the penetrating properties and extended dry time – 16 hours at 25 °C (77 °F) – of this two-component epoxy seal crevices and other imperfections, promoting better adhesion for subsequent coats. For prepared masonry surfaces, V155 penetrates and seals, providing an excellent foundation for subsequent coats of Corotech epoxy floor coatings. The unique, 100% solids formula of V155 forms a sealed epoxy barrier that inhibits future corrosion.

    • Low viscosity easily fills voids and crevices
    • Does not shrink – eliminates craters
    • Chemical and fume resistant
    • Extended cure time allows maximum penetration
    • Seals previously coated concrete, masonry, and galvanized metal
    • Qualifies for LEED certification
    Hide Details

  • Coal Tar Epoxy

    V157

    Show Details

    Coal Tar Epoxy is a high-solids, two-component tar filled coating formulated to provide excellent film build in one or two coats. The high level of cross-linking provides an excellent barrier coat for immersion service in fresh water, salt water or waste water. Additionally, this product is resistant to many acids, alkalis and mild solvents in splash and spill exposures.

    • Formulated for use over properly prepared/primed steel, iron, concrete, and non-ferrous metal
    • Provides excellent protection from water, acids, alkalis, and mild solvents
    • Can be applied directly to the substrate; use with a primer for extra longevity
    • Suitable for use in USDA inspected facilities
    • Meets Performance Requirements for Army Corps of Engineers C-200
    • Meets Performance Requirements for SSPC Paint 16
    • Meets Performance Requirements for DOD-P-23236
    Hide Details
  • Epoxy Mastic Coating

    Epoxy Mastic Coating

    V160

    Show Details

    Epoxy Mastic Coating is a high-solids, rust-inhibitive, surface-tolerant epoxy mastic for professional use in industrial and commercial applications. Ideal for protection of steel and concrete (floor rated). Excellent for use on ferrous and non-ferrous metals, and when properly top-coated, exhibits excellent chemical and moisture resistance. Resists solvents, dilute acids and alkali attack.

    • High solids (79%) and high build – excellent for corners, crevices and welds
    • Surface-tolerant mastic for marginal substrates
    • Hard scratch- and impact-resistant coating
    • Excellent for secondary containment
    • Qualifies for LEED credits
    • Suitable for use in USDA inspected facilities
    Hide Details

  • Epoxy Patch Kit

    V165

    Show Details

    Epoxy Patch Kit is a 100% solids epoxy co-polymer matrix for repairing and patching interior concrete floors. It sets rapidly with extremely high initial strength and is ready for foot traffic in 5-8 hours. This easy-to-use 3-part system includes liquid part A, liquid catalyst and aggregate.

    • 3-part system allows on-site mixing to the exact consistency needed
    • High Solids with no shrinkage
    • For any high-traffic floor
    • Non Flammable with no odour
    • Trowels easily
    Hide Details
  • Moisture Tolerant Quick Set Epoxy Sealer

    Moisture Tolerant Quick Set Epoxy Sealer

    V156

    Show Details

    Organic Zinc Rich Primer is a heavy-duty corrosion inhibitor for interior or exterior ferrous metal and weathered galvanized metal. It is made from an organic thermoplastic resin and leaves a finished film that is 83% zinc. Ideal for touching up existing galvanized metal with no topcoat.

    • High zinc content delivers cathodic protection
    • Can be top coated or left uncoated
    • Thermoplastic resin requires tie coat under certain finishes; check TDS
    • Cold Galvanizing Project Qualification
    • Meets Composition Requirements of TT-P-1046
    • Meets Performance Requirements of TT-P-641 & DOD-P-21035
    • Meets Performance Requirements of Mil-P-26915 Type I, Class A
    • Meets SSPC Paint #5 & SSPC Paint #20, Type II
    Hide Details
  • Polyamide Epoxy Primer

    Polyamide Epoxy Primer

    V150

    Show Details

    Polyamide Epoxy Primer is formulated for use on ferrous and non-ferrous metals in industrial and commercial applications. This two-component, rust-inhibitive epoxy primer is an excellent choice for use as a rust-inhibitive base coat when used as part of a high-performance coating system. With proper top coating, it demonstrates excellent resistance to moisture and chemicals, including solvents, acids, and alkalis. Polyamide Epoxy Primer is also suitable for use on concrete substrates in secondary containment and immersion service applications.

    • High-solids content
    • Outstanding protection against corrosion
    • Engineered for use in general metal finishing and fabrication
    • Also appropriate for chemical processing facilities and transportation infrastructure finishing
    • Suitable as a high-performance tie coat; especially over existing epoxies
    • Suitable for use in USDA-inspected facilities
    Hide Details